GLYN 2M0ETJ (@2m0etj) header
GLYN 2M0ETJ (@2m0etj) profile picture

VHF AND UP ,ALL SATELLITES "AMATEUR AND WX",DIGI MODES AND A BUDDING EME QRP'R ,GENERAL ANTENNA PROJECTS. A practcal rather than academic "HAM".

south west scotland IO85JA
Joined March 2019
Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)Photo by GLYN 2M0ETJ (@2m0etj)
may be of interest to some .
1
136
That's the 1.5m dish frame and its mast plus the replacement tele vhf mast finished just the mesh now and then decide on ant to use have a 23cm septum it seems heavy ! thinking of maybe a patch instead to lower wind stress and physical handling🤔comments greatfully appreciated
2
2
13
369
Thats the front plate ,back plate,ribs and fibreglass antenna support done just the outer band and mid band to fit and the ultralight dish frame is complete and ready for the mesh .jiuggling between 2 masts and the dish at the moment seems to be taking forever 🤨
8
120
Its been a long time getting here but at LAST ive managed to get a RX signal or 2 off the moon on 1296mhz ,still a very long way to go but at least now theres light at the end of the tunnel
1
1
10
313
FINALLY ive got 2x23cm yagis in the air and coax measured,i should have listened more to @g0lbk and just concentrated on a dish but i thought these would be quicker !.i was expecting some detuning when i sealed the DE'S but not this much .TBC next comment
1
5
98
despite being close to within .1mm one is ok but one has detuned down to 1275 so only be rx for a while 🙄. at least if the rx is ok it will drive me on .the new dish is going ok and new mast is almost done but been held up waiting for spares from china to repair the mill🙄.
1
1
71
satellite antenna will be removed before use 😉
58
James clerk maxwell rs special event station now on 7 .108 GB2JCM
1
1
2
228
Also on 14.285 13:00
2
114
14.285. 13.12pm GB2JCM
61
14.285. 13.12pm GB2JCM
50
The James Clerk Maxwell Radio Society Nearly there, Saturday 14th and Sunday 15th June we will be operating from Parton Kirk with the call GB2JCM we hope to work your station over the weekend band conditions permitting!! please share
2
1
1
165
James Clerk Maxwell was born on June 13, 1831, and he died on November 5, 1879. He is buried at Parton Kirk, near Castle Douglas in Dumfries and Galloway, Scotland
51
About now, 81 years ago, D-Day and the liberation of Western Europe began. We remember those who gave all so that we today have everything. May God give them eternal rest and peace.
3
1
11
169
"FINALLY" im moving foward getting on 23cm,just finished 2x23ele ants as a temporary measure until my dish is eventually finished, just a bit of finishing around the D/E's !.its been over 12 months since i started to build them ,had to go to plan B.....TBC
1
6
305
..... as i could not figure out how to build the bent dipoles on the dg7ybn designs and get them soldered so had to go with folded dipoles for the D/E ,have to see how they perform once in use .im a huge fan of dg7's
1
2
122